Welcome to Silverfish. This site uses cookies. Read our policy.

 

DETERMINE WHICH TRANSFER SEATPOST WILL FIT YOUR BIKE

 

Follow the steps below to determine which FOX Transfer Seatpost will work best for you and your bike frame. This guide can be a helpful tool for selecting the appropriate model of FOX Transfer Seatpost before purchase. You will need your frame and original rigid seatpost to make this determination.

Complete User Specification Drawings for the FOX Transfer Seatpost that contain additional information are shown at the bottom of this page.

 

You can download the PDF Owner's Manual for the FOX Transfer Seatpost by clicking: Transfer Seatpost

 

 

STEP 1

 

With your original seatpost set to your desired ride height, measure from the top of the seat collar to the center of the saddle rails. This will be Measurement "A".

Compare measurement "A" to the charts below to determine the maximum travel Transfer Seatpost that will work for your application. 

 

img/help/page802-CEOZ/FIT-Aa-m.jpg

 

Measurement A Transfer Travel (Internal Routing)   Measurement A Transfer Travel (Exteral Routing)
209.55mm - 355mm 150mm   224.4mm - 359.9mm 150mm
185.5mm - 305mm 125mm   199.5mm - 310mm 125mm
160.5mm - 255mm 100mm   174.3mm - 259.8mm 100mm

 

If your measurement "A" does not fall within any of the tables in step 1 above, please contact FOX.

If your measurement "A" falls within the tables in step 1 above, continue below to check for proper insertion clearance within the frames seat tube.

 

 

STEP 2

 

You will also need to check that the FOX Transfer Seatpost will fit deep enough into your frame without contacting any internal part within the frame.

Carefully insert your original seatpost fully into the frame until it contacts any obstruction. This could be a suspension pivot or a bend in the seat tube. Measure from the top of the seat collar to the center of the saddle rails again. This will be Measurement "B".

img/help/page802-CEOZ/FIT-B-m.jpg

 

STEP 3

 

Remove the original seatpost and measure from the bottom of the post to the center of the saddle rails. This will be measurement "C". 

Subtract measurement "B" from measurement "C" to determine measurement "D".

 

img/help/page802-CEOZ/FIT-C-m.jpg

 

 

STEP 4

 

Add measurement "A" to measurement "D".

Compare "A" + "D" to the charts below to verify that at your desired saddle height, the FOX Transfer will be able to insert deep enough into your frame without contacting any internal part within the frame. 

Your "A" + "D" value must be equal to or greater than the number in the table below for that specific post to work with your frame.

 

Measurement A + D Transfer Travel (Internal Routing)   Measurement A Transfer Travel (Exteral Routing)
485mm+ 150mm   461mm+ 150mm
434mm+ 125mm   411mm+ 125mm
384mm+ 100mm   361mm+ 100mm

 

If your measurement "A"+"D" does not fall within any of the tables in step 4 above, please contact FOX. 

 

 

 

USER SPECIFICATION DRAWINGS

 

Transfer Seatpost Internal Routing

img/help/page802-CEOZ/Transfer-Seatpost-Internal-Routing-User-Specifications-m.jpg

 

Transfer Seatpost External Routing

img/help/page802-CEOZ/Transfer-Seatpost-Collar-Routing-User-Specifications-m.jpg

Silverfish UK Ltd. Units 3a-3c Woodacre Court, Saltash Parkway Industrial Estate, Burraton Road, Saltash, Cornwall, United Kingdom, PL12 6LY
Silverfish UK Ltd. (Registration No. 4075057).

Technical specifications are for guidance only and cannot be guaranteed accurate. All offers are subject to availability and while stocks last. Errors and omissions excepted. Silverfish UK Limited acts as a credit intermediary and only offers credit products for Close Brothers Retail Finance. Its registered office is: Close Brothers Group plc, 10 Crown Place, London EC2A 4FT. Credit is subject to application and status.

Powered by Netalogue